Author Topic: Post Your Guns (Read 2181101 times)

couch · « **Reply #1845 on:** July 09, 2010, 02:15:27 AM »

Quote from: sokoloka;3309678

This definitely sounds like something that I'd be interested in.

Looking at this:
http://www.tacticalmachining.com/products.php?pid=28#images/490_345-80-lower.jpg

All I'd need to do would follow the mapped out finishing steps and pick up an upper kit? $80 sound deece for the receiver above?

Here is most of the basics. Most 80% will be pretty much the same work as this.

http://www.cncguns.com/projects/ar15lower80tutorial-2.html

BOUNCEHOUSE420 · « **Reply #1846 on:** July 09, 2010, 11:22:11 AM »

The final milling needs to be done by or under the close supervision of the owner

couch · « **Reply #1847 on:** July 09, 2010, 12:14:02 PM »

Pretty sure all of it needs to be done by the final owner.

couch · « **Reply #1848 on:** July 09, 2010, 12:37:36 PM »

Handle this... 60%ish 1911 castings. No machining has been done but some parts are good to go with minimal/zero fitting. This is pretty much what mine started out as but it had a few of the holes finished already. I may pick up one or two of these...

http://www.gunco.net/forums/f259/fs-60ish-1911-castings-55389/

BOUNCEHOUSE420 · « **Reply #1849 on:** July 09, 2010, 12:56:02 PM »

Quote from: couch;3309842

Pretty sure all of it needs to be done by the final owner.

im trying to find where i read what i said hold up

dont bother trying to buy a lpk from ctd if youre in ca they freak out an yell

BOUNCEHOUSE420 · « **Reply #1850 on:** July 09, 2010, 01:08:54 PM »

found it here in post 36... i know ive seen it elsewhere too
http://www.calguns.net/calgunforum/showthread.php?t=110703&highlight=80%25lower

couch · « **Reply #1851 on:** July 09, 2010, 02:40:09 PM »

Handle this... 60%ish 1911 castings. No machining has been done but some parts are good to go with minimal/zero fitting. This is pretty much what mine started out as but it had a few of the holes finished already. I may pick up one or two of these...

http://www.gunco.net/forums/f259/fs-60ish-1911-castings-55389/

farva · « **Reply #1852 on:** July 09, 2010, 02:45:55 PM »

dont know how i never stumbled upon this thread... Just a few of the pistols and a play gun at the bottom

________
Vapor genie

Birdmane · « **Reply #1853 on:** July 09, 2010, 02:50:27 PM »

Sweet guns.

couch · « **Reply #1854 on:** July 09, 2010, 02:56:06 PM »

Handle this... 60%ish 1911 castings. No machining has been done but some parts are good to go with minimal/zero fitting. This is pretty much what mine started out as but it had a few of the holes finished already. I may pick up one or two of these...

http://www.gunco.net/forums/f259/fs-60ish-1911-castings-55389/

Admiral Ackbar · « **Reply #1855 on:** July 09, 2010, 02:56:20 PM »

Whats the second to last one?

Birdmane · « **Reply #1856 on:** July 09, 2010, 02:57:34 PM »

I think its a thompson center contender

farva · « **Reply #1857 on:** July 09, 2010, 03:22:37 PM »

Quote from: Birdmane;3309927

I think its a thompson center contender

yeah, iv got three of them. haha. and if it is the one above you were wondering about?? its a taurus .45
________
Vapor Genie Vaporizer

BOUNCEHOUSE420 · « **Reply #1858 on:** July 09, 2010, 03:24:42 PM »

i want a judge real bad

edit: what the hell is the one above the judge?

king_palm · « **Reply #1859 on:** July 09, 2010, 05:55:00 PM »

1911 carbine conversion.
couch is crying right now.

Im wondering how you guys in cali deal with all those shitty gun laws.

Bouncehouse you should have ordered it from Riflegear

Bikeguide.org - Bike maintenance for BMX'ers · « **Reply #1859 on:** July 09, 2010, 05:55:00 PM »

Author Topic: Post Your Guns (Read 2181101 times)

BOUNCEHOUSE420

BOUNCEHOUSE420

BOUNCEHOUSE420

BOUNCEHOUSE420

Bikeguide.org - Bike maintenance for BMX'ers