Author Topic: What have you made? (Read 554205 times)

Big_L · « **Reply #210 on:** February 02, 2012, 12:18:30 PM »

Quote from: Admiral Ackbar;3524517

this is so sick

thanks! took about an hour with a glue gun. it's my first run at seat wrapping

Alex. · « **Reply #211 on:** February 03, 2012, 04:05:00 PM »

Hell yeah! Lots of cool stuff on the page. Here's something I just finished making. Jack stand dollies. Same concept as regular wheel dollies only with these you can still freely move the vehicle while it's torn down. Made the bases out of 1 1/2"x1/8" angle iron and added two 12"x2"x1/8" "out-riggers" on each dolly for more stability. Welded 6 pivoting 2" metal casters to each as well for any discrepancies in the floor. Cost was around $120 for all of them.

If you plan on making some of these, I got the casters off of Amazon for $2 each which was the cheapest I could find them, otherwise everywhere had them for over $4 per caster.

Cut the 1 1/2" angle to 30" and cut out the bends every 7 1/2".

Bent it and welded everything else together gets you one of these!

Big_L · « **Reply #212 on:** February 03, 2012, 04:20:34 PM »

alex, you are a genious

SnorkelPaterson · « **Reply #213 on:** February 03, 2012, 04:37:20 PM »

Quote from: Admiral Ackbar;3524517

this is so sick

Genius..

BOUNCEHOUSE420 · « **Reply #214 on:** February 03, 2012, 05:14:43 PM »

Quote from: alex.;3525044

Hell yeah! Lots of cool stuff on the page. Here's something I just finished making. Jack stand dollies. Same concept as regular wheel dollies only with these you can still freely move the vehicle while it's torn down. Made the bases out of 1 1/2"x1/8" angle iron and added two 12"x2"x1/8" "out-riggers" on each dolly for more stability. Welded 6 pivoting 2" metal casters to each as well for any discrepancies in the floor. Cost was around $120 for all of them.

If you plan on making some of these, I got the casters off of Amazon for $2 each which was the cheapest I could find them, otherwise everywhere had them for over $4 per caster.

Cut the 1 1/2" angle to 30" and cut out the bends every 7 1/2".

Bent it and welded everything else together gets you one of these!

those will work great until they hit that crack in the floor just right and your car ends up on the ground. its not fun getting a car off the ground that has no wheels ask me how i know:mad2:. the only way id trust them is if they were under a solid axle or some how solidly attached to the frame and welded to the dollies. i actually thought about making some but it sketched me out too much.

cup.o.dirt · « **Reply #215 on:** February 03, 2012, 05:19:13 PM »

Quote from: BOUNCEHOUSE420;3525054

those will work great until they hit that crack in the floor just right and your car ends up on the ground. its not fun getting a car off the ground that has no wheels ask me how i know:mad2:. the only way id trust them is if they were under a solid axle or some how solidly attached to the frame and welded to the dollies. i actually thought about making some but it sketched me out too much.

Quoted for truth, ratchet strap those bitches to whatever its sitting on so it cant slide off.

sokoloka · « **Reply #216 on:** February 03, 2012, 07:56:13 PM »

Those are also going to be a bitch to jack off of unless you chock them some how. Even then seems like they'd be tipsy.

midwestmax · « **Reply #217 on:** February 03, 2012, 08:23:31 PM »

Quote from: accidentprone;3524426

Nintendo coffee table and Mustache coat rack...

This is sick.

BOUNCEHOUSE420 · « **Reply #218 on:** February 03, 2012, 08:42:53 PM »

Quote from: sokoloka;3525071

Those are also going to be a bitch to jack off .

Cuz they're metal and dont have dicks?

Alex. · « **Reply #219 on:** February 03, 2012, 11:48:52 PM »

Thanks for all the input guys! They are very sturdy, they feel no different than if it was just on jack stands. Obviously you roll it carefully, not go balls to the wall and hope for the best. I don't even have the smoothest garage floor but it rolled with ease to the other side of the garage. Even rolled it over that crack without even noticing. Loving them. They will also double as a regular wheel dolly.

Putting it up onto the jacks was actually less sketchy as the other jack didn't want to tip over as I jacked the opposite side up, it would just roll across the floor in unison with the jack. Then I jacked up the whole rear at the same time and plopped them into place. Not worried at all.

Bunsincunsin · « **Reply #220 on:** February 05, 2012, 10:16:07 AM »

I started this over holiday break and I'm just now finishing it up. It's a 29 gallon vivarium that I'm planning on putting a group of three Phyllobates vittatus in (poison dart frogs).

Alex. · « **Reply #221 on:** February 05, 2012, 02:44:45 PM »

What if they get out?!

Bunsincunsin · « **Reply #222 on:** February 05, 2012, 04:22:16 PM »

It's enclosed, so they can't...

Alex. · « **Reply #223 on:** February 05, 2012, 06:37:39 PM »

I mean break out. Like, just lunge themselves at the glass until it lets loose. Prison break style.

BabyJesus[NJ] · « **Reply #224 on:** February 12, 2012, 07:40:58 PM »

pointless grip and "silencer" for my BB gun

and 2 more shift knobs

Bikeguide.org - Bike maintenance for BMX'ers · « **Reply #224 on:** February 12, 2012, 07:40:58 PM »

Author Topic: What have you made? (Read 554205 times)

BOUNCEHOUSE420

BOUNCEHOUSE420

Bikeguide.org - Bike maintenance for BMX'ers