Author Topic: What did you do to your bike today? (v2) (Read 2279446 times)

paranoidmexican · « **Reply #2640 on:** January 09, 2013, 10:57:16 PM »

got some goodies, shitty picture but i got some WTP bar ends that go over the bars like a cap. flatland fuel! not pictured is the griptape for my pegs

Sasha · « **Reply #2641 on:** January 10, 2013, 03:56:03 AM »

Started taking it to bits to de ruust it, turns out my mum's husband has lost the allen key I need for my brakes out of a packet I hadn't even opened yet. Sure there's a thread for this too "people who take things without asking", because my answer would have been no. Why are people incapable of putting things back where they got them?

thirks · « **Reply #2642 on:** January 10, 2013, 07:10:26 AM »

cunts tom, thats why

Pat · « **Reply #2643 on:** January 10, 2013, 08:39:24 AM »

Put my mothership together to get my beacon evaluated by united.

CMB · « **Reply #2644 on:** January 10, 2013, 06:00:27 PM »

Thanks to the awesome guys at Profile I was able to send my Push faceplate back and buy a new one. Then I went to Home Depot to get a new bolt for my pedal spindle.

Gary · « **Reply #2645 on:** January 10, 2013, 08:47:45 PM »

Built up a new back wheel for my Solid. 10T Madera V2

mrjimyjohn · « **Reply #2646 on:** January 10, 2013, 09:49:38 PM »

Quote from: CMB;3622742

Thanks to the awesome guys at Profile I was able to send my Push faceplate back and buy a new one. Then I went to Home Depot to get a new bolt for my pedal spindle.

how much did profile charge you? just out of curiosity...

CMB · « **Reply #2647 on:** January 11, 2013, 07:33:20 AM »

Just 7 bucks for shipping, which I thought was really cool of them.

Meursault · « **Reply #2648 on:** January 13, 2013, 04:28:32 PM »

Broke the axle in my madera front hub, relaced my vandero2 back up. Bummed on non matching hubs now.

Sasha · « **Reply #2649 on:** January 13, 2013, 04:48:04 PM »

Tried to clean the rest off my frame. Rust remover doesn't work as good as the internet lead me to believe.

_tom_ · « **Reply #2650 on:** January 13, 2013, 05:09:51 PM »

WD40 + wire wool?

Sasha · « **Reply #2651 on:** January 14, 2013, 02:55:32 AM »

Yeah I'm going to go do that today, I was just hoping that the rust remover would make it effortless. No such luck.

ron_weasley_T1 · « **Reply #2652 on:** January 14, 2013, 03:07:43 AM »

I just used fine grit wet and dry and it's come up a treat....and you know the condition of it previously.

Admiral Ackbar · « **Reply #2653 on:** January 14, 2013, 03:40:36 AM »

took my geisha apart and found out my clutch has a fairly deep groove worn in it from the friction ball-springs so i took them out and rigged up my own way to get friction (with tape) now i can fakie without having my shit randomly engage, also tightened my pedal so they don't rattle, now my bike doesn't make a single rattle when i bounce it on its tires. then rode it in the garage, did some wallrides, sliders, and fakie hop one handers.

so amped on bikes right now gonna check out the indoor bowl a few towns over tomorrow

thirks · « **Reply #2654 on:** January 14, 2013, 06:34:54 AM »

got new forks then used a scotchbrite pad to take the shine off them so they match my frame better

Bikeguide.org - Bike maintenance for BMX'ers · « **Reply #2654 on:** January 14, 2013, 06:34:54 AM »

Author Topic: What did you do to your bike today? (v2) (Read 2279446 times)

Pat

Bikeguide.org - Bike maintenance for BMX'ers