Author Topic: Quick Questions (Read 923512 times)

Austin Tasseltine · « **Reply #525 on:** January 07, 2013, 07:50:30 AM »

Quote from: Ralph Wiggum;3621599

Anyone else had a frame with an integrated headset that required tapping the bearings (a couple taps with a rubber mallet) into the head tube? Every other frame I've owned I was able to push the bearings in by grabbing on the opposite end of the head tube and using my thumbs to get the bearing to seat.

yep.

weedbix · « **Reply #526 on:** January 07, 2013, 08:00:52 AM »

Integrated should be slip-fit

JohnW · « **Reply #527 on:** January 07, 2013, 08:04:45 AM »

Quote from: Sasha;3621610

^I've had that before. There's probably paint or something in there. Wouldn't worry about it.

My bike has succumbed to the British Winter, has anyone tried this shit:

or should I just paint it red? I don't mind a bit of humidity brown cool rust but this is orange shit rain rust and we can't be having that.

I'm guessing it's phosphoric acid based. That stuff has to soak in to work and requires multiple coats. It'd be hard to use on a BMX frame cause it'd just drip off. It says non-drip so it might work, but I have a feeling it still will. If it actually stays on the tube let me know because I'd be interested in picking up some. I used similar stuff on the floor of my car and had to let it soak for hours, wire wheel it, and repeat a couple times.

If you soak it in clean motor oil and let it bake in the sun (or a warm lamp since you're in England) a little it'll turn the rust brown and slow it down. That's what I did to my S&M and I love how it turned out. Or use a brass wire wheel to polish the bare steel, then oil it.

weedbix · « **Reply #528 on:** January 07, 2013, 08:08:20 AM »

Using the sun is not an option in an English winter

JohnW · « **Reply #529 on:** January 07, 2013, 08:09:25 AM »

Quote from: Professor Horatio Hufnagel;3621618

Using the sun is not an option in an English winter

Which is why I suggested a warm lamp. An incandescent bulb decently close should work well enough.

toady · « **Reply #530 on:** January 07, 2013, 10:11:04 AM »

Narcoleptic Insomniac · « **Reply #531 on:** January 09, 2013, 01:35:24 PM »

What do you guys use to lube your chain and how well does it work?

I've been using the White Lightning waxy type stuff but it doesn't last very long until my chain starts squeaking again.

Kinchy · « **Reply #532 on:** January 09, 2013, 02:02:44 PM »

Tf2 oil.

mrjimyjohn · « **Reply #533 on:** January 09, 2013, 02:50:35 PM »

I use 3-in-1 electric motor oil. (the blue one)

It works nice, and it gets kind of sticky after a while and turns into a gum sort of substance that coats the teeth on my sprocket and driver. I believe this is because it's vegetable based, but I'm not sure. I probably re-apply it every few months, or whenever I ride in the rain.

Sasha · « **Reply #534 on:** January 09, 2013, 02:59:11 PM »

Quote from: JohnW;3621617

I'm guessing it's phosphoric acid based. That stuff has to soak in to work and requires multiple coats. It'd be hard to use on a BMX frame cause it'd just drip off. It says non-drip so it might work, but I have a feeling it still will. If it actually stays on the tube let me know because I'd be interested in picking up some. I used similar stuff on the floor of my car and had to let it soak for hours, wire wheel it, and repeat a couple times.

If you soak it in clean motor oil and let it bake in the sun (or a warm lamp since you're in England) a little it'll turn the rust brown and slow it down. That's what I did to my S&M and I love how it turned out. Or use a brass wire wheel to polish the bare steel, then oil it.

I just ordered some spray on stuff, will let you know how it goes!

macandcheese · « **Reply #535 on:** January 13, 2013, 03:25:35 PM »

how the fuck does stuff like this happen

sunday funday 2

Sasha · « **Reply #536 on:** January 13, 2013, 03:34:13 PM »

Quote from: Sasha;3622360

I just ordered some spray on stuff, will let you know how it goes!

It wasn't great.

Object · « **Reply #537 on:** January 14, 2013, 11:12:58 AM »

What's the preferred grease for a freecoaster?
Finish Line Teflon?

JohnW · « **Reply #538 on:** January 14, 2013, 11:32:14 AM »

Quote from: Object;3623704

What's the preferred grease for a freecoaster?
Finish Line Teflon?

Teflon is best for chains and brake cables.

I've been using this on freecoasters for a few years, works great:

Still have the same tube I bought over 3 years ago. I've also been using it on cranks, headset bearings, bearing seats, hub bearings, etc.

Object · « **Reply #539 on:** January 14, 2013, 11:52:31 AM »

Cheers.

Bikeguide.org - Bike maintenance for BMX'ers · « **Reply #539 on:** January 14, 2013, 11:52:31 AM »

Author Topic: Quick Questions (Read 923512 times)

Bikeguide.org - Bike maintenance for BMX'ers