Multimedia

Author Topic: Quick Questions  (Read 922570 times)

0 Members and 9 Guests are viewing this topic.

Offline Sammm

  • Sr. Member
  • ****
  • Posts: 3462
    • View Profile
Re: Quick Questions
« Reply #735 on: May 20, 2013, 04:45:18 AM »
^Pretty sure it depends on the lever. Some levers the cable will come out along the underside of the bar and goes under the tape, some (I guess higher end levers) will run the cable through the bars. If yours goes through the bars, you will of course need a hole for the cable to exit.
Quote from: Big Ben;2799842
are you sure tom mann didnt impregnate your mother?

shaolin sword style

Offline Kinchy

  • Fux wit titles
  • Veteran
  • *****
  • Posts: 8496
    • View Profile
Re: Quick Questions
« Reply #736 on: May 20, 2013, 02:01:27 PM »
Almost definitely no. If you need a hole, it will alread have a hole.
Quote from: Broady;3529439
I ran ahead a bit and hid, dropped my jeans and took my top off and started chasing them whilst spraying beer all over them and making weird noises.

Offline Admiral Ackbar

  • O.G. Member
  • ******
  • Posts: 14867
    • View Profile
Re: Quick Questions
« Reply #737 on: May 31, 2013, 10:54:18 PM »
phil wood definitely makes flip/flop fixed/free hubs. and fyi you can thre
Do Phil Wood make a track rear hub with a fixed cog on one side and a freewheel on the other? I can't see anything on their site.

When putting barend brakelevers on bullhorn bars does the cable go inside the bar and would I need to drill a hole for it to go to the callipers?

PW fixed/free hub 120 spaced : http://www.bikeman.com/BTI-PW81236.html?
utm_source=GoogleBase&utm_medium=GoogleBase&utm_campaign=GoogleBase&gclid=CIyWnfT5wbcCFQbNOgoda0cAFg

cable routing is all down to the bars, if theres two holes near the stem, run it internally, if not go under the tape
Quote from: blueee;3557172
i went to a rave at a zoo one time. although i didnt give the dolphins heroin substitute

Offline hugh.

  • Pedo-Slayer
  • Sr. Member
  • ****
  • Posts: 2603
    • View Profile
Re: Quick Questions
« Reply #738 on: June 07, 2013, 05:31:31 PM »
Perfect. thanks guys.

Offline Narcoleptic Insomniac

  • Veteran
  • *****
  • Posts: 8598
    • View Profile
Re: Quick Questions
« Reply #739 on: June 10, 2013, 10:54:43 AM »
Will my Odyssey Classic Race fork take a 2.35" Fly Ruben or should I just go with the 20.15"? The rim is a Hazard Lite.

Offline mrjimyjohn

  • Sr. Member
  • ****
  • Posts: 844
    • View Profile
Re: Quick Questions
« Reply #740 on: June 10, 2013, 04:00:15 PM »
I really doubt it would fit, those fuckers inflate pretty wide.
Bike Check

With enough lube and brute force, anything is possible.

Offline Prodigal Son

  • Sr. Member
  • ****
  • Posts: 2371
  • has no pubes
    • View Profile
Re: Quick Questions
« Reply #741 on: June 10, 2013, 06:49:39 PM »
My 2.15 Ruben is roughly the same width as a 2.35 aaron ross.

Offline Narcoleptic Insomniac

  • Veteran
  • *****
  • Posts: 8598
    • View Profile
Re: Quick Questions
« Reply #742 on: June 10, 2013, 10:02:23 PM »
2.15" Ruben it is then. Thanks dudes.

Offline Zoidberg

  • Doctor
  • Veteran
  • *****
  • Posts: 6605
    • View Profile
Re: Quick Questions
« Reply #743 on: June 16, 2013, 12:08:16 PM »
can you convert a federal v2 (i think) freecoaster to female?

Offline tim_sch

  • Member
  • ***
  • Posts: 496
    • View Profile
Re: Quick Questions
« Reply #744 on: June 16, 2013, 04:47:52 PM »
There are no V3 or Greyhound replacement axles available, so I'd guess no.

Offline Spev

  • Sr. Member
  • ****
  • Posts: 1119
    • View Profile
Re: Quick Questions
« Reply #745 on: June 16, 2013, 05:02:06 PM »
can you convert a federal v2 (i think) freecoaster to female?

Sure you can. You can either cut, drill and tap it out yourself, Have some one else do it for you, or buy one of the aftermarket axles from companies using KHE style internals.

Offline smalley

  • B(g Veteran)
  • Sr. Member
  • ****
  • Posts: 2428
    • View Profile
Re: Quick Questions
« Reply #746 on: June 17, 2013, 05:04:30 PM »
What will stop my eclat tibia cranks wobbling?
SLOOT

Offline mrjimyjohn

  • Sr. Member
  • ****
  • Posts: 844
    • View Profile
Re: Quick Questions
« Reply #747 on: June 17, 2013, 08:33:42 PM »
What will stop my eclat tibia cranks wobbling?

T/Wom/thunderbolts.























Sorry, I had to. Locktite or plumbers tape often work as a band aid fix, but if it's actually worn splines causing the problem there isn't a whole lot you can do about it. Is it the drive or non drive side? Edit: nevermind, tibias are actually welded 2 piece aren't they?
« Last Edit: June 17, 2013, 08:35:16 PM by mrjimyjohn »
Bike Check

With enough lube and brute force, anything is possible.

Offline NewYorkRider

  • Jr. Member
  • **
  • Posts: 31
    • View Profile
Re: Quick Questions
« Reply #748 on: June 18, 2013, 08:28:05 PM »
Is there a hubguard for a v2 hazard hub that wont spread frame kinda like the knight guard for the primo.

Brooklynrider

  • Guest
Re: Quick Questions
« Reply #749 on: June 18, 2013, 08:51:59 PM »
BSD for the odyssey

Bikeguide.org - Bike maintenance for BMX'ers

Re: Quick Questions
« Reply #749 on: June 18, 2013, 08:51:59 PM »

 

-->

Tell them " Sheepdog sent you", for a little something special

Click this image for a little something special