1
Sell and Swap / In search for an S&M LTF
« on: May 05, 2020, 07:07:18 PM »
I will pay top dollar!
Welcome, Guest. Please login or register.
Did you miss your activation email? November 22, 2024, 10:00:51 AM
Did you miss your activation email? November 22, 2024, 10:00:51 AM
| Multimedia |
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2
The Bike Shop / Re: Fit Aitken S3.5 is BACK
« on: April 10, 2020, 07:20:13 AM »
Dish has been checked, wheel is trued, it’s the frame. At this point I don’t care, I’m having fun on this thing
3
The Bike Shop / Re: Oldest part on your BMX?
« on: February 14, 2020, 12:38:45 PM »
Madera 19mm cranks and a knight cable hanger
4
Bike Gallery / Re: Fit Aitken
« on: February 03, 2020, 09:37:25 AM »
With me seat that low I’m not sitting to pedal obviously...I’m 140lbs and have a skinny butt, and the seat has more padding than you think it does. It’s not bad. Not better or worse than a mid pivotal, just different
5
The Bike Shop / Re: Fit Aitken S3.5 is BACK
« on: January 18, 2020, 06:00:58 PM »
It’s off, the picture doesn’t quite do it justice. And I will eventually have brakes on it, I wish it was centered. And before I bought those spacers, it was fucking hell even getting it slightly straight. It would just pull extremely hard to the right. I’m ok, it’s a nice frame and faster geo than my SFA.
6
The Bike Shop / Re: Fit Aitken S3.5 is BACK
« on: January 18, 2020, 05:23:38 PM »
I tried pushing it, running a 28/9. Sooooo close. So I got the 3mm spacers putting the backend at 13.768, and I’m ok with.
7
Bike Gallery / Re: Fit Aitken
« on: January 18, 2020, 05:19:06 PM »Fit Aitken 3.5 21” Frame
Odyssey R33 forks, trimmed steerer tube
S&M Race bars, 9.25 w/Duo Bohan grips and Odyssey Parends
Fiend Reynolds stem v2, Fiend headset cap, Zodiac headset cover
Madera 175mm cranks, Tree light sprocket 25t, Odyssey JCPC pedals
Odyssey Antigram rear hub w/ 3/8s axle, Gsport Volcano bolts, Simple 3mm wheel slammers
Gsport Rolloway front hub, Gsport Volcano bolts
Sun rims, Dt spokes
Odyssey Aitken 2.4 front tire, Odyssey Path pro 2.25 rear
Odyssey Bluebird chain
Odyssey Hawk seat, Fit post
10
The Bike Shop / Re: Fit Aitken S3.5 is BACK
« on: January 18, 2020, 10:16:05 AM »
I’ll stick to my screenshot of Fit’s chain length guide (put together by leading industry experts!) that has served me with perfectly slammed backends with outstanding chain tension with my last 6 or 7 frames. But thank you for your expert opinions professor! I’m glad my posts prompted you to insert your backend knowledge on a dying forum.
11
The Bike Shop / Re: Fit Aitken S3.5 is BACK
« on: January 12, 2020, 08:33:56 PM »Are the wheel slammer things on the outside of the dropouts?Yes. And yes. The wheel slammed perfect on a 13.75 backend running a 27-9 ratio. I normally don’t even buy a frame unless I can slam the backend. Now with this frame and 3mm simple spacers and a 25-9, the wheel won’t sit straight. Even without the spacers the wheel pulls extremely hard to the right when I tighten it down. Never seen this on an aftermarket frame 17 years of riding. And believe me I’m a nerd about bike stuff.
Is your wheel dished?
12
The Bike Shop / Re: Fit Aitken S3.5 is BACK
« on: January 04, 2020, 11:09:34 PM »
No hubguard, odyssey Antiguan with 3/8s axle. I just bought those Simple wheel slammers, it did the trick perfectly for chain tension, the wheel is still pulled towards the drive side. I sold a T1 SFA for this frame! Whatever...bike check tomorrow
13
The Bike Shop / Re: Fit Aitken S3.5 is BACK
« on: January 01, 2020, 06:46:31 PM »
I got one, 21’’ in tan. Beautiful frame with die cut stickers. I’ve had a hell of a time getting the backend straight though, it pulls real hard to the drive side when you even slightly tighten the bolts, it’s like it’s off or something.
14
Sell and Swap / 21” Raw SFA
« on: January 18, 2019, 09:48:37 AM »
Barely even been built, no pegs, removable mounts. No dents, dings, rashes, deep scratches or rusting. 340 shipped. 6822152175. I’m not going to sell this forever.
15
The Bike Shop / Re: New hub what’s BG recommend if anyone’s out there
« on: October 14, 2018, 09:19:01 AM »
dont get a freecoaster, they are all shitty and require you to run your chain loose. I’m running the Odyssey Antigram with a 3/8 axle, I love it! Also the newer Profile/Maderas with the chromoly female axles are nice, just make sure your bearings are seated correctly
 Tell them " Sheepdog sent you", for a little something special |
 Click this image for a little something special |
