common bearing and bolt/nut sizes

[big_papa_nuts]

this will be a compiled list of common bearing and bolt/nut thread sizes.

Bearings


6000
-Odyssey Vandero hub
-Primo N4 hub


6202
-Geisha/Federal/Reverse non drive side hub bearing


6303
-Reloader non drive side hub bearing


6802
-Profile cassette driver bearing (9t^)
-Geisha/Federal/Reverse driver bearings
-Primo Mix driver bearings (& needle/bushing)
-Proper driver bearings
-Madera driver bearings


6804
-Gsport Marmoset bearing


6902
-Odyssey cassette body bearing
-Odyssey driver bearing (10t^)
-Primo Pro driver bearing
-Demolition Anorexia hub bearing
-Proper Magnalite 2


6903
-Madera hub bearing
-Primo Mix cassette hub bearing
-Odyssey Vandero2 hub bearing
-Profile Mini hub bearing


6904
-Gsport Homer hub bearings
-Gsport Monkey hub bearings


7905
-Geshia/Reloader/Federal/Reverse the drive side hub bearinga


R12
-MID 19mm bb bearing


hk1210
-Fly Ruben pedals (roller bearing)


697zz (697 2rs)
-Fly Ruben pedals (sealed bearing)  
 


Profile Hub bearing set.


Nice site for sealed bearing dimensions, etc.
http://www.endurobearings.com/products/enduro_bearings.html


thanks for contributing; alittlekidsbike, Ride2Live2Ride, super.chief, marsh, BurlyAsFack, theboredbmxer

[couch]

Threaded bits

1/4 - .875
-Profile Slim Jim clamp bolt


5/16-18
-most american made stem bolts
-RNC spindle thread


5/16-24
-Unsealed Jim C locknut


3/8-24
-Profile cranks
-The House/Premium female axles
-Gsport Marmoset/Monkey hub (1.5" length)
-Odyssey Vandero2
-Stolen Team crank spindle
-Colony Clone hub
-Demolition Mary Kate hub
-Shadow Raptor hub
-Superstar Overdrive hub


3/8-26
-KHE Gaysha hub
-most thru axle front hubs
-Primo Jewels/Andys nuts


3/8-16
-Profile mini female axles (1.5" length)
-Madera female axle

M4x0.70
- S&M / Fit Gyro tab

M5x0.80
- Odyssey Evo Knarp bolts (5mm length)


M6x1.0
-standard brake mounts (20mm length)
-removable brake mounts (15mm length)
-brake pads
-Odyssey brake lever bolts (15 & 20mm length)


M8x1.25
-most overseas stem bolts
-Primo pinchbolts
-Stolen Team cranks sprocket bolt (small)
-Fit cranks sprocket bolt (small)


M10x1.0
-Twombolt sprocket bolt
-Wombolt spindle bolt (solid)
-Wombolt sprocket bolt
-Wethepeople Supreme front hub bolts
-Flybikes hub bolt
-Eclat hub bolts


M10x1.25
-Oversize Star Nut
-S&M/Fit Compression Cap
-Tree H10 Compression Cap


M10x1.5
-Pivotal seat bolt (50mm length)
-Stolen Team cranks sprocket bolt (large)
-Fit cranks sprocket bolt (large)



M11x1.0
-Primo spindle


9/16-18
-Gsport Homer bolts/helicoil


9/16-20
-right pedal/crank



9/16-20 (left hand)
-left pedal/crank



M12x1.25
-Twombolt spindle bolt  (hollow)
-Profile GDH (extra hollow) crank bolts



M14x1.0
-14mm axles


M14 x 1.25
-Gsport Ratchet bolts



M15 x 1
-Flybikes cranks.


M20x1.5
-Tree bar ends

M24x1.5
-Odyssey Compression Cap
-Standard Byke Compression Cap
-ZodiacEng. Compression Cap


M25x1.5
-Stln Compression Cap


1.37x24
-euro bottom brackets
-freewheel thread


Excellent source for custom bolts and conversion kits;     Blue Six Bikes



thanks for contributing; pegs, Leon_Sumbitches, don-231, big_papa_nuts, JeffersonC, jonathan, super.chief, Ride2Live2Ride, Pedrofsky, atxboy, Andras, Ainsworth112294

[RideFour15]

M8x1.25
-most overseas stems
-primo pinchbolts

Any metric stem I've used was size 6, not 8.

[RideFour15]

Nope, you have always used a 6mm wrench.  That has nothing to do with the threads.  A G-Sport uses a 9/16" wrench, but has 3/8" threads.

I didn't realize M8 was the thread, I thought it was the size of the bolt like the imperial ones listed before it.  So is the 1.25 the length of the bolt then?

[greenreese]

I didn't realize M8 was the thread, I thought it was the size of the bolt like the imperial ones listed before it.  So is the 1.25 the length of the bolt then?

Picture book.

[don-231]

primo euro bb bearing size anyone?

[reebzor]

Anyone know the measurements for Thomson elite seat post and elite road stem.

thanks.

*edit: Stem face are M5x18mm and the steer tube are M5x21mm

[couch]

Kenny, hate to correct you, but I know for a fact that the RNC bolts are 3/8"-16tpi. Why? Because I ran them in my mini front hub for about 6 months.

I know for a FACT that the RNC cranks I WAS RUNNING before I bought Wombolts used a 5/16-18 thread in each end of the spindle. As with most small companies, a running change is completely possible. They may have changed this up considering the heads on the 5/16-18 bolts pulled off of the thread. The broach was too deep on the ones I had, and the 3/16" broach intersected with the minor diameter of the thread.

I know this because I had to shorten my spindle, remill the square and drill/tap the thread deeper on one side. I also used one of my stem bolts when I had to tighten the cranks since both of the spindle bolts broke, as mentioned above.

There was nothing wrong with the spindle length, however if you remember, I faced the back of the arms so I needed to shorten the spindle. I wanted a smaller Q-Factor.

Anyways, long story short, mine were 5/16-18, yours were 3/8-16.

[.Lee.]

What's the threading on a star fangled nut? One like this, incase there is two sizes.

[couch]

bearing for 19mm spindle.

Spanish bottom brackets use modified 6904's

The 22mm spindle version is 20mmx37mmx9mm
The "19mm" is .750"x37mmx9mm

Reason I put 19mm in "" is because it isn't 19mm. It uses a .750" (3/4") ID, not 19mm. Profile cranks and the like are not 19mm. They are 3/4". Do not get the two confused, they are not compatable.

.750" = 19.05mm
0.05mm = .002"

In terms of bearing/spindle fit .002" is wayyyyyyy too much press.

Id your bearing was in reality 19mm your spindle wouldn't fit unless it was made .002" undersize, which is highly unlikely.

So to answer your question, the bearing you are looking for is a modified 6904 with a 3/4" ID. You won't find this anywhere but at a bike shop.

[couch]

The Tree H10 headset cap is the same thread as the freestyle starnut... It is also the same thread used on S&M/Fit forks.

M10x1.25

[couch]

22mm MID bearing isn't an off the shelf bearing. You're only going to find them at bike shops.

They are based off the R12 bearings which is 3/4" x 1-5/8" x 7/16" IDxODxW respectively.

22mm MID bearings are 22mm x 1-5/8" x 7/16"

[Ride2Live2Ride]

Spanish Bearings......


go big: http://www.flickr.com/photos/29414553@N02/3705492407/sizes/o/


go big: http://www.flickr.com/photos/29414553@N02/3705491333/sizes/o/

[couch]

Pumped on your stuff Nick.
:cheers:

[Ride2Live2Ride]

Pumped on your stuff Nick.
:cheers:

Thanks man. I will try to keep posting stuff over the year ( a lot this week). I just have to creep around my old hard drive and see what I am able to post. I almost wish I still had my bike so I could rip off some more random bearing sizes and information.....